DFI LanParty UT NF3 250GB - Specifications

(Page 2 of 14 )

As for the motherboard itself, here's the specs to get you started:

CPU

• AMD Athlon 64 (up to 3700+)
• Socket 754

Chipset

• nVIDIA® nForce3 250Gb

Memory

• Three 184-pin DDR SDRAM DIMM sockets
• Supports single channel (64-bit wide) memory interface
• Supports up to 3GB memory when using DDR333, supports up to 2GB memory when using DDR400
• Supports PC2700 (DDR333) and PC3200 (DDR400) DDR SDRAM DIMM
• Supports x8/x16, non-ECC, up to 512Mb DDR devices
• Supports unbuffered DIMM

BIOS

• Award BIOS
• CPU/DRAM/AGP overclocking
• CPU/DRAM/Chipset overvoltage
• 4Mbit flash memory
• AMD Cool'n'Quiet technology

Power Management

• Supports ACPI specification and OS Directed Power Management
• Supports ACPI STR (Suspend to RAM) function
• Wake-On-Events include:
     - Wake-On-PS/2 Keyboard/Mouse
     - Wake-On-Ring (external modem)
     - Wake-On-LAN
     - RTC timer to power-on the system
• AC power failure recovery

Hardware Monitor

• Monitors CPU/system temperature
• Monitors 12V/5V/3.3V/Vcore/Vbat/Vsb/Vnb/Vdram/Vagp voltages
• Monitors CPU/chassis fan speed
• CPU Overheat Protection function monitors CPU temperature during system boot-up

Audio

• Realtek ALC850 8CH audio CODEC
• Supports Microsoft® DirectSound/DirectSound 3D
• S/PDIF-in/out interface

LAN

• Marvell 88E1111 GbE PHY
• 10/100/1000BASE-T IEEE 802.3 compliant

IDE

• Two IDE connectors support four UltraDMA 133Mbps hard drives
• NVIDIA RAID supports spanning across Serial ATA and Parallel ATA
• RAID 0, RAID 1, RAID 0+1 and JBOD

Serial ATA with RAID

• Supports four SATA interfaces with speed up to 1.5Gbps
  • Two Serial ATA ports supported by nForce3 250Gb chip 
  • Two Serial ATA ports supported by Marvell SATA PHY
• NVIDIA RAID supports spanning across Serial ATA and Parallel ATA
• RAID 0, RAID 1, RAID 0+1 and JBOD

IEEE 1394 (optional)

• VIA VT6307 controller
• Supports two 100/200/400 Mb/sec ports

AGP

• Supports AGP 8x up to 2132MB/sec. and AGP 4x up to 1066MB/sec. bandwidth for 3D graphics applications
• Supports 0.8/1.5V add-in cards

Rear Panel I/O Ports

• 1 PS/2 mouse port
• 1 PS/2 keyboard port
• 1 DB-9 serial port
• 1 DB-25 parallel port
• 2 S/PDIF RCA jacks (S/PDIF-in and S/PDIF-out)
• 1 IEEE 1394 (Optional)
• 1 RJ45 LAN port
• 4 USB 2.0/1.1 ports
• 6 audio jacks for 8CH audio output

I/O Connectors

• 2 connectors for 4 additional external USB 2.0/1.1 ports
• 1 connector for 1 external IEEE 1394 port (Optional)
• 1 front audio connector for external line-out and mic-in jacks
• 1 CD-in internal audio connector
• 1 S/PDIF connector for optical cable connection
• 1 IrDA connector
• 4 Serial ATA connectors
• 2 IDE connectors
• 1 floppy connector
• 2 ATX power supply connectors (20-pin and 4-pin)
• 1 front panel connector
• 3 fan connectors for CPU fan, chassis fan and 2nd fan
• EZ touch switches (power switch and reset switch)

Expansion Slots

• 1 AGP slot that supports 8x/4x AGP
• 5 PCI slots

PCB

• ATX form factor
• 30.5cm (12") x 24.5cm (9.44")

All specifications above are subject to change without prior notice.

Next: Chipset Integration >>
 

More Motherboards Articles
More By DMOS

Comments On: DFI LanParty UT NF3 250GB

· DFI was kind enough to inform me that the LanpartyUT series is replacing the...    · Good review overall. the "odd" SATA connectors you talk about are quite common on ...    · I've owned 4 differnt socket 754 mobos since Feb 2004. Two were VIA and 2 were nF3...    · I ordered 7 Lanparty 250Gb machines as upgrades for my work. It was a bit of a risk...    · Why couldn't have it been 128-bit?!? I have 2 512mb OCZ dual channels not being...   >>> Post your comment now!